|
Who's Online
There currently are 6043 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
It is perfect, exactly what we needed. It's like the paper version but less clutter.
;
Received my manual within 24 hours. Very clear scan of the manual I needed. Thanks!
;
Very clear scan, I recommend it. Definitely a must have for any 3362 owner.
Alpine could have written a slightly more complete manual, though. It's already pretty huge, but the unit has so many functions, I feel some more explanation would have been better.
Yamaha's manual of their comparable YDSP-1 is a little better in my opinion.
;
Immediate response with excellent service - highly reccommended
;
Correct manual received and of good quality but the contents of the file for the Service Manual for the same monitor is for a 20" TV not the RGB Monitor.
SYSTEM OPERATION
6. Selecting the UH/UB-1K Transmitters Group & Channel Setting
Both the UH/UB-1K transmitters have to be programmed for the channel and group selected on the UWS-1K receiver via the IR reception link between the receiver and transmitter during the �rst 20 seconds after the transmitter is powered up. As soon as the transmitter LEDs light up indicating Power ON, the Transfer Button (18) on the UWS-1K receiver must be pressed once while the MAIN MENU is being displayed. The Power LED (9) of the receiver will �ash quickly indicating IR transmission to the transmitters of the Group and Channels selected on the receiver is in progress. Successful transfer is complete when the Signal Strength indicator on the receiver�s LCD Display (10) indicates a received signal from the transmitter being programmed. Press Transfer (18) again to stop when this happens or just let it expire in 20 seconds automatically. (Important note: there is no other way to program the Group and Channel selected in the UWS-1K receiver into the UH/UB1K transmitters so the above procedure must be followed carefully.)
UWS-1K RECEIVER
7. Rack-mounting the Receiver
There are two options available for rackmounting the UWS-1K: single or side-by-side with another UWS-1K receiver. a. Single mounting: Just attach the optional Rack Ears (1) to each side slot and tighten with supplied screws (as shown). b. Side-by-side mounting: Attach the two optional Join Pieces (2) and tighten the four supplied screws. Then attach the rack ears to each side slot and tighten with supplied screws (as shown). (Note: Do not mount the receiver on a rack directly above an ampli�er or other source of high heat. This could degrade the performance of the UWS-1K. Always ensure adequate air�ow and heat dissipation in any rack con�guration.)
8. Installing Antennas
Install antennas by connecting the two Antennas (3) included with your system to the two RF Screw-On Connectors (4) located on the back of your UWS-1K receiver. The optimal positions of the antennas are 45 degrees from the receiver and 90 degree from each other. For maximum range, it is always best to maintain a line of sight (no obstructions) between the receiver antennas ant the transmitter at all time whenever possible.
9. Powering the Receiver
To power the receiver, plug the AD-DC adaptor (16.5VDC/0.4A) provided into the DC Input Jack (5) on the back of the receiver. Then plug the adapter into an AC outlet. (Note: Any 16.5VDC source with 400mA capacity can also be used.) Connect either the XLR Balanced (6) or 1�4� Unbalanced Output (7) to your mixing board, effect, or ampli�er. To turn ON, press the Power Switch (8) for 2 second. The Power LED (9) will light and the LCD Display (10) will show the Group (11), Channel (11) assignment, RF Level Meter (12), Diversity (13), and the audio AF LED (15) displays (when the transmitter is activated). To turn OFF, press the Power Switch (8) for 3 seconds and release. The receiver will turn off.
5
|
|
|
> |
|